Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
We've noticed the article relating to A Step-by-Step Guide to Installing a Bathtub directly below on the net and felt it made sense to write about it with you on this site.
Installing a tub isn't specifically rocket science, yet it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bath tub with a new one is also a moderately tough task. If the old bathtub is readily available, the job can relocate rapidly; if you need to open up a wall to remove the old tub as well as place the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly require a helper to leave the old bathtub and embeded in the new one. Make certain you have certified yourself for the work and also fit attempting it. As opposed to working with a service provider to take over a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This article will certainly assist you mount a brand-new tub in your restroom if you have currently gotten a new bathtub and do not require to alter the plan of your previous supply of water pipes.
Your tools and material list need to consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing taps can be fairly problematic due to the limited access that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will originate from the pipelines. When the supply pipelines have been removed, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning during this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers are in location in between the tap as well as the sink. Safeguard the tap in place with the supplier provided backnut. Once the tap is safely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former type ought to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Using the two wooden boards under its feet, place the bath tub in the called for position. The wood boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub up until the level reviews degree.
To mount taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Switch on the water system as well as examine all joints and also brand-new pipework for leaks as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet and the regular outlet for leakages.
Lastly, repair the bathroom paneling as described in the producer's instruction manual. Tiling and securing around the bathtub needs to wait till the bath tub has actually been used at the very least when as this will certainly resolve it right into its last placement.
Planning for the Installment
To start with, the sustaining framework supplied with the bath should be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the bath tub.
Fit the flexible faucet ports to the bottom of both taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to break an inflexible seal, creating the water to penetrate the wall in between the bathroom and also the tiling, leading to problems with moisture as well as possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill the tub with water before securing, to permit the motion experienced when the tub remains in use. The sealer can split relatively very early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly readily available on the market. It is advisable to fit the floor tiles utilizing waterproof or water-proof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that segment was a smart idea. Are you aware of another person who is inquisitive about the topic? Feel free to share it. I am grateful for your time. Please check up our website back soon.
Ring, relax, resolved! Report this page